AUDIO-TECHNICA AT-OC9XML
Dual moving coil stereo cartridge with Microlinear stylus | Weight: 7.6g | Frequency response 20 - 47,000 Hz
SPEDIZIONE GRATUITA
Se effettui un ordine superiore a € 300 con due o più prodotti, la spedizione sarà gratuita. Le tempistiche stimate di spedizione sono indicate.
Paga in modo semplice e sicuro con Carta di credito, Contrassegno, AMEX, PayPal e Bonifico bancario. La tua privacy è garantita da connessioni sicure.
Tutti i prodotti sono coperti da Garanzia convenzionale di 2 anni. Risolviamo problemi di qualsiasi natura con professionalità e correttezza.
Solo tramite eMail dal Lunedì al Venerdì dalle ore 9:30 alle 15:00.
Dual moving coil stereo cartridge with Microlinear stylus. Weight: 7.6g. Frequency response 20 - 47,000 Hz
The next generation of the legendary OC9 cartridge series
Since its introduction more than 30 years ago, Audio-Technica's pioneering OC9 moving coil cartridge series has been praised by discerning listeners and professional critics for its musical transparency, sound expression and precise construction. Featuring a square shank for accurate stylus alignment and a bare diamond for enhanced fine detail retrieval.
FEATURES
- Features a bare microline stylus and boron cantilever offering lower distortion and high transient response
- A neodymium magnet and permendur yoke provide significantly increased magnetic energy
- Features threaded inserts in the cartridge body
- Aluminium body minimises unwanted vibrations for reduced resonance and superior reproduction
- PCOCC is used for coils to achieve pure signal transmission
- Weight 7.6 g
- Dimensions 17.3 (H) x 16.8 (W) x 25.7 (D) mm
Microlinear stylus
The microlinear diamond profile offers a high-frequency response with less wear and distortion than elliptical or conventional linear contact stylus.
Aluminium body
Aluminium body minimises unwanted vibrations for reduced resonance and superior audio reproduction
Easy mounting
Threaded holes in the cartridge body allow it to be mounted on the Shell a or integral arm with just two M2.6 screws - no nuts or bolts required.
Accessories included
- 1 non-magnetic screwdriver
- 1 brush
- 2 washers
- 4 pairs of mounting screws: 5 mm, 8 mm, 10 mm, 12 mm
- 1 plastic protector
In the event that the compliance value is stated at 100 Hz (usually referring to Japanese cartridges), it simply has to be doubled to find its correspondence at 10 Hz. On the other hand, if the compliance is declared in static regime (usually on cartridges made in the USA), it must be halved to find its value at 10 Hz.
To check whether the resonance frequency is between 8-12 Hz (preferably 9-11 Hz), the optimum value, proceed via the links below.
- Model AT-OC9XML
- 1/2’ centre mounting / Threaded
- Frequency response 20 - 47,000 Hz
- Body material Aluminium
- Channel separation 27 dB (1 kHz)
- Output channel balance 1.0 dB (1 kHz)
- Output voltage 0.4 mV (@ 1 kHz, 5 cm / sec)
- Vertical tracking angle 20 degrees
- Vertical tracking force range 1.8 to 2.2 g (standard 2.0 g)
- Microlinear stylus
- Stylus dimensions 2.2 x 0.12 mil
- Stylus construction Bare square stylus
- Bare boron cantilever 0.28 mm Ø
- Coil impedance 12 Ohm (1 kHz)
- Coil inductance 25 μH (1 kHz)
- DC resistance 12 Ohm
- Citance, Dynamic Compliance static 20 x 10 - 6 cm / dyne
- Capacitance, Dynamic Compliance: 16 x 10 - 6 cm / dyne (100 Hz)
- Brass terminal pins
- Wire used for PCOCC coil (continuous copper melting process Ohno.)
- Recommended load impedance Min 100 Ohm
- Cartridge weight 7.6 g
- Dimensions 17.3 (H) x 16.8 (W) x 25.7 (D) mm